commit 1be59c97c83ccd67a519d8a49486b3a8a73ca28a upstream.
An UAF can happen when /proc/cpuset is read as reported in [1].
This can be reproduced by the following methods:
1.add an mdelay(1000) before acquiring the cgroup_lock In the
cgroup_path_ns function.
2.$cat /proc/<pid>/cpuset repeatly.
3.$mount -t cgroup -o cpuset cpuset /sys/fs/cgroup/cpuset/
$umount /sys/fs/cgroup/cpuset/ repeatly.
The race that cause this bug can be shown as below:
(umount) | (cat /proc/<pid>/cpuset)
css_release | proc_cpuset_show
css_release_work_fn | css = task_get_css(tsk, cpuset_cgrp_id);
css_free_rwork_fn | cgroup_path_ns(css->cgroup, ...);
cgroup_destroy_root | mutex_lock(&cgroup_mutex);
rebind_subsystems |
cgroup_free_root |
| // cgrp was freed, UAF
| cgroup_path_ns_locked(cgrp,..);
When the cpuset is initialized, the root node top_cpuset.css.cgrp
will point to &cgrp_dfl_root.cgrp. In cgroup v1, the mount operation will
allocate cgroup_root, and top_cpuset.css.cgrp will point to the allocated
&cgroup_root.cgrp. When the umount operation is executed,
top_cpuset.css.cgrp will be rebound to &cgrp_dfl_root.cgrp.
The problem is that when rebinding to cgrp_dfl_root, there are cases
where the cgroup_root allocated by setting up the root for cgroup v1
is cached. This could lead to a Use-After-Free (UAF) if it is
subsequently freed. The descendant cgroups of cgroup v1 can only be
freed after the css is released. However, the css of the root will never
be released, yet the cgroup_root should be freed when it is unmounted.
This means that obtaining a reference to the css of the root does
not guarantee that css.cgrp->root will not be freed.
Fix this problem by using rcu_read_lock in proc_cpuset_show().
As cgroup_root is kfree_rcu after commit d23b5c577715
("cgroup: Make operations on the cgroup root_list RCU safe"),
css->cgroup won't be freed during the critical section.
To call cgroup_path_ns_locked, css_set_lock is needed, so it is safe to
replace task_get_css with task_css.
[1] https://syzkaller.appspot.com/bug?extid=9b1ff7be974a403aa4cd
Fixes: a79a908fd2 ("cgroup: introduce cgroup namespaces")
Signed-off-by: Chen Ridong <chenridong@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Shivani Agarwal <shivani.agarwal@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The locks_remove_posix() function in fcntl_setlk/fcntl_setlk64 is designed
to reliably remove locks when an fcntl/close race is detected. However, it
was passing in the wrong filelock owner, it looks like a mistake and
resulting in a failure to remove locks. More critically, if the lock
removal fails, it could lead to a uaf issue while traversing the locks.
This problem occurs only in the 4.19/5.4 stable version.
Fixes: a561145f3a ("filelock: Fix fcntl/close race recovery compat path")
Fixes: d30ff33040 ("filelock: Remove locks reliably when fcntl/close race is detected")
Cc: stable@vger.kernel.org
Signed-off-by: Long Li <leo.lilong@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 82dbb57ac8d06dfe8227ba9ab11a49de2b475ae5 upstream.
Some firmware versions of the 9600 series SAS HBA byte-swap the REPORT
ZONES command reply buffer from ATA-ZAC devices by directly accessing the
buffer in the host memory. This does not respect the default command DMA
direction and causes IOMMU page faults on architectures with an IOMMU
enforcing write-only mappings for DMA_FROM_DEVICE DMA driection (e.g. AMD
hosts).
scsi 18:0:0:0: Direct-Access-ZBC ATA WDC WSH722020AL W870 PQ: 0 ANSI: 6
scsi 18:0:0:0: SATA: handle(0x0027), sas_addr(0x300062b2083e7c40), phy(0), device_name(0x5000cca29dc35e11)
scsi 18:0:0:0: enclosure logical id (0x300062b208097c40), slot(0)
scsi 18:0:0:0: enclosure level(0x0000), connector name( C0.0)
scsi 18:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y)
scsi 18:0:0:0: qdepth(32), tagged(1), scsi_level(7), cmd_que(1)
sd 18:0:0:0: Attached scsi generic sg2 type 20
sd 18:0:0:0: [sdc] Host-managed zoned block device
mpt3sas 0000:41:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0021 address=0xfff9b200 flags=0x0050]
mpt3sas 0000:41:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0021 address=0xfff9b300 flags=0x0050]
mpt3sas_cm0: mpt3sas_ctl_pre_reset_handler: Releasing the trace buffer due to adapter reset.
mpt3sas_cm0 fault info from func: mpt3sas_base_make_ioc_ready
mpt3sas_cm0: fault_state(0x2666)!
mpt3sas_cm0: sending diag reset !!
mpt3sas_cm0: diag reset: SUCCESS
sd 18:0:0:0: [sdc] REPORT ZONES start lba 0 failed
sd 18:0:0:0: [sdc] REPORT ZONES: Result: hostbyte=DID_RESET driverbyte=DRIVER_OK
sd 18:0:0:0: [sdc] 0 4096-byte logical blocks: (0 B/0 B)
Avoid such issue by always mapping the buffer of REPORT ZONES commands
using DMA_BIDIRECTIONAL (read+write IOMMU mapping). This is done by
introducing the helper function _base_scsi_dma_map() and using this helper
in _base_build_sg_scmd() and _base_build_sg_scmd_ieee() instead of calling
directly scsi_dma_map().
Fixes: 471ef9d4e4 ("mpt3sas: Build MPI SGL LIST on GEN2 HBAs and IEEE SGL LIST on GEN3 HBAs")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240719073913.179559-3-dlemoal@kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e1fd567d32fcf7544c6e09e0e5bc6c650da6e23 upstream.
This commit changes device mapper, so that it returns -ERESTARTSYS
instead of -EINTR when it is interrupted by a signal (so that the ioctl
can be restarted).
The manpage signal(7) says that the ioctl function should be restarted if
the signal was handled with SA_RESTART.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10a04ff09bcc39e0044190ffe9f00f998f13647c upstream.
Currently, tools have *ALIGN*() macros scattered across the unrelated
headers, as there are only 3 of them and they were added separately
each time on an as-needed basis.
Anyway, let's make it more consistent with the kernel headers and allow
using those macros outside of the mentioned headers. Create
<linux/align.h> inside the tools/ folder and include it where needed.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ccbfcac05866ebe6eb3bc6d07b51d4ed4fcde436 upstream.
The recent addition of a sanity check for a too low start tick time
seems breaking some applications that uses aloop with a certain slave
timer setup. They may have the initial resolution 0, hence it's
treated as if it were a too low value.
Relax and skip the check for the slave timer instance for addressing
the regression.
Fixes: 4a63bd179fa8 ("ALSA: timer: Set lower bound of start tick time")
Cc: <stable@vger.kernel.org>
Link: https://github.com/raspberrypi/linux/issues/6294
Link: https://patch.msgid.link/20240810084833.10939-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b8f9c1fb464968a5b18d3acc1da8c00bad24fad upstream.
The Wacom driver maps the HID_DG_TWIST usage to ABS_Z (rather than ABS_RZ)
for historic reasons. When the code to support twist was introduced in
commit 50066a042d ("HID: wacom: generic: Add support for height, tilt,
and twist usages"), we were careful to write it in such a way that it had
HID calculate the resolution of the twist axis assuming ABS_RZ instead
(so that we would get correct angular behavior). This was broken with
the introduction of commit 08a46b4190d3 ("HID: wacom: Set a default
resolution for older tablets"), which moved the resolution calculation
to occur *before* the adjustment from ABS_Z to ABS_RZ occurred.
This commit moves the calculation of resolution after the point that
we are finished setting things up for its proper use.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Fixes: 08a46b4190d3 ("HID: wacom: Set a default resolution for older tablets")
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 538fd3921afac97158d4177139a0ad39f056dbb2 upstream.
hci_conn_params_add() never checks for a NULL value and could lead to a NULL
pointer dereference causing a crash.
Fixed by adding error handling in the function.
Cc: Stable <stable@kernel.org>
Fixes: 5157b8a503 ("Bluetooth: Fix initializing conn_params in scan phase")
Signed-off-by: Griffin Kroah-Hartman <griffin@kroah.com>
Reported-by: Yiwei Zhang <zhan4630@purdue.edu>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit df24373435f5899a2a98b7d377479c8d4376613b ]
DPU debugging macros need to be converted to a proper drm_debug_*
macros, however this is a going an intrusive patch, not suitable for a
fix. Wire DPU_DEBUG and DPU_DEBUG_DRIVER to always use DRM_DEBUG_DRIVER
to make sure that DPU debugging messages always end up in the drm debug
messages and are controlled via the usual drm.debug mask.
I don't think that it is a good idea for a generic DPU_DEBUG macro to be
tied to DRM_UT_KMS. It is used to report a debug message from driver, so by
default it should go to the DRM_UT_DRIVER channel. While refactoring
debug macros later on we might end up with particular messages going to
ATOMIC or KMS, but DRIVER should be the default.
Fixes: 25fdd5933e ("drm/msm: Add SDM845 DPU support")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/606932/
Link: https://lore.kernel.org/r/20240802-dpu-fix-wb-v2-2-7eac9eb8e895@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ae738dfef2c0323752ab81786e2d298c9939321 ]
If promiscuous mode is disabled when there are fewer than four multicast
addresses, then it will not be reflected in the hardware. Fix this by
always clearing the promiscuous mode flag even when we program multicast
addresses.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240822154059.1066595-2-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0b39e2dc7017ac667b70bdeee5293e410fab2fb ]
nft_counter_reset() resets the counter by subtracting the previously
retrieved value from the counter. This is a write operation on the
counter and as such it requires to be performed with a write sequence of
nft_counter_seq to serialize against its possible reader.
Update the packets/ bytes within write-sequence of nft_counter_seq.
Fixes: d84701ecbc ("netfilter: nft_counter: rework atomic dump and reset")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 932021a11805b9da4bd6abf66fe233cccd59fe0e ]
Function hci_sched_le needs to update the respective counter variable
inplace other the likes of hci_quote_sent would attempt to use the
possible outdated value of conn->{le_cnt,acl_cnt}.
Link: https://github.com/bluez/bluez/issues/915
Fixes: 73d80deb7b ("Bluetooth: prioritizing data over HCI")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 116523c8fac05d1d26f748fee7919a4ec5df67ea ]
Change that introduced the use of __check_timeout did not account for
link types properly, it always assumes ACL_LINK is used thus causing
hdev->acl_last_tx to be used even in case of LE_LINK and then again
uses ACL_LINK with hci_link_tx_to.
To fix this __check_timeout now takes the link type as parameter and
then procedure to use the right last_tx based on the link type and pass
it to hci_link_tx_to.
Fixes: 1b1d29e51499 ("Bluetooth: Make use of __check_timeout on hci_sched_le")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: David Beinder <david@beinder.at>
Stable-dep-of: 932021a11805 ("Bluetooth: hci_core: Fix LE quote calculation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b1d29e5149990e44634b2e681de71effd463591 ]
This reuse __check_timeout on hci_sched_le following the same logic
used hci_sched_acl.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Stable-dep-of: 932021a11805 ("Bluetooth: hci_core: Fix LE quote calculation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a830bbce3af16833fe0092dec47b6dd30279825 ]
The hrtimer function callback must not be NULL. It has to be specified by
the call side but it is not validated by the hrtimer code. When a hrtimer
is queued without a function callback, the kernel crashes with a null
pointer dereference when trying to execute the callback in __run_hrtimer().
Introduce a validation before queuing the hrtimer in
hrtimer_start_range_ns().
[anna-maria: Rephrase commit message]
Signed-off-by: Phil Chang <phil.chang@mediatek.com>
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73964c1d07c054376f1b32a62548571795159148 ]
It is possible that the host connected and saw a cm established
event and started sending nvme capsules on the qp, however the
ctrl did not yet see an established event. This is why the
rsp_wait_list exists (for async handling of these cmds, we move
them to a pending list).
Furthermore, it is possible that the ctrl cm times out, resulting
in a connect-error cm event. in this case we hit a bad deref [1]
because in nvmet_rdma_free_rsps we assume that all the responses
are in the free list.
We are freeing the cmds array anyways, so don't even bother to
remove the rsp from the free_list. It is also guaranteed that we
are not racing anything when we are releasing the queue so no
other context accessing this array should be running.
[1]:
--
Workqueue: nvmet-free-wq nvmet_rdma_free_queue_work [nvmet_rdma]
[...]
pc : nvmet_rdma_free_rsps+0x78/0xb8 [nvmet_rdma]
lr : nvmet_rdma_free_queue_work+0x88/0x120 [nvmet_rdma]
Call trace:
nvmet_rdma_free_rsps+0x78/0xb8 [nvmet_rdma]
nvmet_rdma_free_queue_work+0x88/0x120 [nvmet_rdma]
process_one_work+0x1ec/0x4a0
worker_thread+0x48/0x490
kthread+0x158/0x160
ret_from_fork+0x10/0x18
--
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 261341a932d9244cbcd372a3659428c8723e5a49 ]
The max_zeroout is of type int and the s_extent_max_zeroout_kb is of
type uint, and the s_extent_max_zeroout_kb can be freely modified via
the sysfs interface. When the block size is 1024, max_zeroout may
overflow, so declare it as unsigned int to avoid overflow.
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20240319113325.3110393-9-libaokun1@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e8477aeb46dfe74e829c06ea588dd00ba20c8cc ]
Fix IUCV_IPBUFLST-type buffers virtual vs physical address confusion.
This does not fix a bug since virtual and physical address spaces are
currently the same.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b432bf376c9c198a7ff48f1ed14a14c0ffbe1fe ]
The unflatten_and_copy_device_tree() function contains a call to
memblock_alloc(). This means that memblock is allocating memory before
any of the reserved memory regions are set aside in the setup_memory()
function which calls early_init_fdt_scan_reserved_mem(). Therefore,
there is a possibility for memblock to allocate from any of the
reserved memory regions.
Hence, move the call to setup_memory() to be earlier in the init
sequence so that the reserved memory regions are set aside before any
allocations are done using memblock.
Signed-off-by: Oreoluwa Babatunde <quic_obabatun@quicinc.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fdbc20036acda9e5694db74a032d3c605323005 ]
If pnfsd_update_layout() is called on a file for which recovery has
failed it will enter a tight infinite loop.
NFS_LAYOUT_INVALID_STID will be set, nfs4_select_rw_stateid() will
return -EIO, and nfs4_schedule_stateid_recovery() will do nothing, so
nfs4_client_recover_expired_lease() will not wait. So the code will
loop indefinitely.
Break the loop by testing the validity of the open stateid at the top of
the loop.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f0639b4d6f649338ce29c62da3ec0787fa08cd1 ]
This fixes attempting to access past ethhdr.h_source, although it seems
intentional to copy also the contents of h_proto this triggers
out-of-bound access problems with the likes of static analyzer, so this
instead just copy ETH_ALEN and then proceed to use put_unaligned to copy
h_proto separetely.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36959d18c3cf09b3c12157c6950e18652067de77 ]
If GET_SEGNO return NULL_SEGNO for some unecpected case,
update_sit_entry will access invalid memory address,
cause system crash. It is better to do sanity check about
GET_SEGNO just like update_segment_mtime & locate_dirty_segment.
Also remove some redundant judgment code.
Signed-off-by: Zhiguo Niu <zhiguo.niu@unisoc.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f40a3ea94881f668084f68f6b9931486b1606db0 ]
The BUG_ON is deep in the qgroup code where we can expect that it
exists. A NULL pointer would cause a crash.
It was added long ago in 550d7a2ed5 ("btrfs: qgroup: Add new qgroup
calculation function btrfs_qgroup_account_extents()."). It maybe made
sense back then as the quota enable/disable state machine was not that
robust as it is nowadays, so we can just delete it.
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e80e3f732cf53c64b0d811e1581470d67f6c3228 ]
Change BUG_ON to a proper error handling in the unlikely case of seeing
data when the command is started. This is supposed to be reset when the
command is finished (send_cmd, send_encoded_extent).
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fbc6f4ac1f4907da4fc674251527e7dc79ffbf6 ]
The may_destroy_subvol() looks up a root by a key, allowing to do an
inexact search when key->offset is -1. It's never expected to find such
item, as it would break the allowed range of a root id.
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be73f4448b607e6b7ce41cd8ef2214fdf6e7986f ]
The pointer to root is initialized in btrfs_init_delayed_node(), no need
to check for it again. Change the BUG_ON to assertion.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2d5bccaca3e8c09c9b9c8485375f7bdbb2631d2 ]
simple_realloc() frees the original buffer (ptr) even if the
reallocation failed.
Fix it to behave like standard realloc() and only free the original
buffer if the reallocation succeeded.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240229115149.749264-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69b0194ccec033c208b071e019032c1919c2822d ]
simple_malloc() will return NULL when there is not enough memory left.
Check pointer 'new' before using it to copy the old data.
Signed-off-by: Li zeming <zeming@nfschina.com>
[mpe: Reword subject, use change log from Christophe]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20221219021816.3012-1-zeming@nfschina.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bea747f3fbec33c16d369b2f51e55981d7c78d0 ]
Since NUM_XMIT_BUFFS is always 1, building m68k with sun3_defconfig and
-Warraybounds, this build warning is visible[1]:
drivers/net/ethernet/i825xx/sun3_82586.c: In function 'sun3_82586_timeout':
drivers/net/ethernet/i825xx/sun3_82586.c:990:122: warning: array subscript 1 is above array bounds of 'volatile struct transmit_cmd_struct *[1]' [-Warray-bounds=]
990 | printk("%s: command-stats: %04x %04x\n",dev->name,swab16(p->xmit_cmds[0]->cmd_status),swab16(p->xmit_cmds[1]->cmd_status));
| ~~~~~~~~~~~~^~~
...
drivers/net/ethernet/i825xx/sun3_82586.c:156:46: note: while referencing 'xmit_cmds'
156 | volatile struct transmit_cmd_struct *xmit_cmds[NUM_XMIT_BUFFS];
Avoid accessing index 1 since it doesn't exist.
Link: https://github.com/KSPP/linux/issues/325 [1]
Cc: Sam Creasey <sammy@sammy.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org> # build-tested
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20240206161651.work.876-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
